Search for an environmental test chamber and you will find the same kind of equipment called a climatic chamber, climate chamber, temperature chamber, thermal chamber, humidity chamber or simply a test chamber. Some of these names mean the same thing. Others describe genuinely different equipment that runs different tests. This guide sorts out the terminology so you can find the right type of chamber, and then points you to the range we supply in Australia and New Zealand.

The Quick Answer
Environmental chamber is the umbrella term. Most of the time it means a climatic chamber: a chamber that controls temperature and humidity. A temperature chamber or thermal chamber is the same thing without humidity control. Everything else (thermal shock, rapid temperature change, altitude, battery, weathering, corrosion and ingress chambers) is a specialised type built for one family of tests.
Chamber Names and What They Mean
| Name you will see | What it means | Browse |
|---|---|---|
| Environmental chamber / environmental test chamber | The umbrella term for any chamber that reproduces service conditions: temperature, humidity, pressure, light, corrosion or dust. | All environmental test equipment |
| Climatic chamber / climate chamber | A chamber that controls temperature and humidity. In practice this is what most people mean by an environmental chamber. | Temperature & humidity chambers |
| Temperature chamber / thermal chamber | Temperature control only, with no humidity system. Used for dry heat, cold and temperature cycling. | Environmental test chambers |
| Humidity chamber / temperature-humidity chamber | Adds controlled relative humidity, typically up to about 98% RH, for damp heat and condensation testing. | Temperature & humidity chambers |
| Thermal shock chamber | Two or three separate zones. The product moves between hot and cold for a near-instant temperature step. | Thermal shock chambers |
| Rapid temperature change / ESS chamber | A single chamber that ramps temperature fast and under control, used for environmental stress screening. | Rapid temperature change chambers |
| Walk-in / drive-in chamber | A climatic chamber built as a room for large equipment, racks, vehicles or batches of products. | Walk-in chambers |
| Ultra-low temperature chamber | Uses cascade refrigeration to reach about -75 to -85 °C for cold characterisation and storage tests. | Ultra-low temperature chambers |
| Altitude chamber | Combines temperature with low pressure to simulate altitude for aerospace and defence equipment. | Altitude chambers |
| Battery test chamber | An explosion-proof climatic chamber for lithium-ion cells, modules and packs. | Battery test chambers |
| Combined environment (AGREE) chamber | Runs temperature and humidity together with vibration on the same test article. | Combined vibration chambers |
| Weathering chamber | UV or xenon arc lamps reproduce sunlight to age plastics, coatings and outdoor products. | UV & xenon chambers |
| Salt spray / corrosion chamber | Exposes coatings and metals to salt fog or corrosive gas to test corrosion resistance. | Corrosion chambers |
| Sand & dust / rain chamber | Ingress chambers that verify IP ratings for dust and water. | Sand & dust chambers |
Size: Bench-Top, Reach-In or Walk-In
Every climatic chamber type comes in different sizes, and size changes more than the price.
- Bench-top chambers suit components, small assemblies and R&D work, and usually run from a standard power outlet.
- Reach-in (floor-standing) chambers handle most product qualification work and are the most common format in test labs.
- Walk-in and drive-in chambers are rooms for large equipment, racks, vehicles, battery systems or batches of products. They normally need three-phase power, ventilation and site preparation, so plan installation early.
Whatever the size, keep the load small enough for air to circulate around it, and tell the supplier how much heat a powered product gives off. Our guide on how to choose an environmental test chamber covers sizing, ramp rate, humidity envelopes and installation in detail.
What Every Climatic Chamber Has in Common
Under the different names, temperature and humidity chambers share the same building blocks:
- Refrigeration to cool the workspace. A single-stage system typically reaches around -40 °C; colder chambers use cascade (two-stage) refrigeration.
- Heaters to raise the temperature and to make fine corrections at setpoint.
- A humidifier and dehumidification system in humidity chambers, fed with purified water.
- Air circulation to keep temperature and humidity even across the workspace.
- A programmable controller that runs multi-step profiles and logs data.
Specialised chambers add to this. Thermal shock chambers add a second (or third) zone and a transfer mechanism, altitude chambers add a vacuum system, and battery chambers add explosion-proof features. See thermal shock vs rapid temperature change chambers and altitude test chambers for more on those types.
How to Narrow Down the Type
- Start with the test method. Your standard or customer specification (for example IEC 60068-2, MIL-STD-810 or a battery standard such as UN 38.3) tells you which kind of chamber it assumes.
- Decide whether you need humidity. If the test involves damp heat, condensation or moisture, you need a temperature and humidity chamber. If not, a temperature-only chamber is simpler and cheaper.
- Check the speed of temperature change. A step change points to thermal shock. A fast, controlled ramp points to a rapid temperature change chamber. A standard ramp suits a general climatic chamber.
- Add any other stress. Low pressure, vibration, sunlight, salt or dust each call for a specialised chamber.
- Size it. Choose bench-top, reach-in or walk-in based on the product, the number of units and your site.
Environmental Test Chambers in Australia and New Zealand
Finch supplies environmental test chambers across Australia and New Zealand, from bench-top and reach-in climatic chambers to walk-in rooms, along with thermal shock, rapid temperature change, ultra-low temperature, altitude, battery, weathering, corrosion and ingress chambers from Sonacme and LISUN. Browse all environmental test equipment, or send us your test specification and we will help you match it to a chamber.
Frequently Asked Questions
Is a climatic chamber the same as an environmental chamber? Usually, yes. Both terms describe a chamber that controls temperature and, in most cases, humidity. Environmental chamber is also used more broadly to cover altitude, corrosion, weathering and ingress chambers, so a climatic chamber is one type of environmental chamber.
What is a thermal chamber or temperature chamber? A thermal chamber, also called a temperature chamber or temperature test chamber, controls temperature only. It suits dry heat, cold and temperature cycling tests where humidity is not part of the requirement.
What is a humidity chamber used for? A humidity chamber, or temperature and humidity chamber, adds controlled relative humidity to temperature control. It is used for damp heat tests such as IEC 60068-2-78 and IEC 60068-2-30, and for finding corrosion, condensation and moisture-related failures.
What is a walk-in environmental chamber? A walk-in chamber is a climatic chamber built as a room large enough to walk into. It is used for large equipment, racks, vehicles, battery systems or many units tested at once, and usually needs site works such as three-phase power and ventilation.
Do I need a thermal shock chamber or a temperature cycling chamber? It depends on the test method. Thermal shock moves the product between separate hot and cold zones for a near-instant step, while temperature cycling and rapid temperature change ramp a single chamber at a controlled rate. Your standard or customer specification will say which one it requires.