Most environmental test chambers look alike on a brochure: a temperature range, a humidity range and a volume. The specifications that decide whether a chamber can actually run your test profile sit underneath those headline figures. This guide covers what to specify, in the order that avoids buying the wrong chamber. If you are still sorting out the terminology, start with types of environmental test chambers explained.
Start With the Test Standard, Not the Chamber
The test you need to run defines the chamber you need. Write down the standards and profiles first, then match chambers to them.
- IEC 60068-2-1 (cold) and IEC 60068-2-2 (dry heat): temperature-only tests. A temperature chamber without humidity control may be all you need.
- IEC 60068-2-78 (damp heat, steady state) and IEC 60068-2-30 (damp heat, cyclic): need controlled humidity, and the cyclic test needs the chamber to manage condensation through the cycle.
- IEC 60068-2-14 (change of temperature): sets transition rates, which drives the ramp-rate specification.
- Customer or defence specifications (for example MIL-STD-810 climatic methods) often add their own profiles. Get the actual profile, not just the standard number.
Temperature Range Sets the Refrigeration System
The low end of the range matters most, because it decides how the chamber is refrigerated. A single-stage refrigeration system typically reaches around −40 °C. Reaching −60 °C to −70 °C generally needs a cascade (two-stage) system, which costs more and uses more power. Specify the lowest temperature your standard requires, plus a small margin, rather than the lowest you can buy.
Read the Humidity Envelope, Not Just the Humidity Range
A chamber listed as “20–98% RH” cannot reach every humidity at every temperature. Humidity control only works inside a temperature window, and the low-humidity, low-temperature corner is the hardest to hold. Ask for the chamber’s humidity envelope chart and check that every point of your profile sits inside it. Humidity chambers also need a supply of purified or deionised water; plan for this at installation.
Ramp Rate: Ask How It Was Measured
Ramp rates are quoted in °C per minute, but the figure only means something with its conditions attached.
- Average vs linear: an average rate can hide a slow final approach to setpoint. A linear rate holds the same slope across the whole transition.
- Empty vs loaded: quoted rates are usually measured with an empty workspace. A heavy or powered device under test slows the chamber down.
- Range of the ramp: a rate measured from −40 °C to +85 °C is not the same as one measured over a narrower span.
If you need very fast transitions, a rapid temperature change chamber or a thermal shock chamber may suit better. See our guide to thermal shock vs rapid temperature change chambers.
Fluctuation and Uniformity Decide Whether Results Are Valid
Two figures describe how well a chamber holds conditions. Fluctuation is how much the temperature varies over time at one point. Uniformity is how much it varies from point to point across the workspace at the same moment. Your standard may set limits for both. Ask for measured data at the setpoints you will use, and confirm how it was measured; IEC 60068-3-5 and IEC 60068-3-6 describe methods for confirming chamber performance.
Size the Workspace Around the Load
- Leave room for airflow. A device that fills the workspace blocks circulation and spoils uniformity. As a rule of thumb, keep the load well under a third of the workspace cross-section.
- Account for heat from powered devices. A device that dissipates heat while running adds load the chamber must remove, especially at low temperatures. Tell the supplier the wattage.
- Plan cable access. Specify cable ports of the right size and position for power, signal and monitoring leads.
Benchtop, Reach-In or Walk-In
| Format | Typical use | Watch for |
|---|---|---|
| Benchtop | Components, small assemblies, R&D | Limited load and heat dissipation |
| Reach-in (floor-standing) | Most product qualification work | Door size, floor loading, power supply |
| Walk-in or drive-in | Large equipment, vehicles, batteries, many units at once | Site works, installation time, ventilation |
Installation and Service in Australia
- Power: larger chambers usually need a three-phase supply. Confirm the current rating before delivery.
- Cooling: air-cooled condensers reject heat into the room; water-cooled units need a chilled-water or cooling-water supply.
- Access: check door widths, lifts and floor loading on the delivery route.
- Service and calibration: confirm local service support and a calibration path, such as NATA-accredited calibration, before you buy.
Specification Checklist
- Standards and profiles the chamber must run
- Lowest and highest temperature, with margin
- Humidity points, checked against the humidity envelope
- Ramp rate, stated as average or linear, loaded or empty, over which span
- Fluctuation and uniformity limits at your setpoints
- Workspace size, device heat load and cable ports
- Power, cooling, water and site access
- Local service and calibration
Browse our temperature and humidity chambers, thermal shock chambers and the full range of environmental test chambers supplied and supported in Australia by Finch.
Not sure which chamber fits your profile? Send us your test specification and we’ll help you match it.
Frequently Asked Questions
What is the difference between an environmental chamber and a climatic chamber? The terms are usually used interchangeably. Both refer to chambers that control temperature and, often, humidity. “Environmental chamber” is sometimes used more broadly to include corrosion, UV and altitude chambers.
Do I need humidity control? Only if your standard or failure mode involves moisture, such as damp heat tests or condensation-related faults. A temperature-only chamber is simpler and cheaper.
Can one chamber cover temperature cycling and thermal shock? Not usually. Thermal shock moves the device between two zones in seconds, which a single-zone chamber cannot do.