Company Updates

News & Updates

Product launches, guides and what's new at Finch Electronic Solutions. We post more often on LinkedIn — follow along there for the day-to-day.

Follow us on LinkedIn →
4 November 2026

Specifying a high-power DC supply

Maximum voltage, maximum current and rated power aren't interchangeable specifications. Before choosing a programmable DC supply for converter validation or automated test, map each operating point: the voltage and current at each test condition, how quickly the output must change, the control modes and interfaces your sequence needs, and the input supply, cooling and installation available.

View the ADG+ seriesView DC power supplies
2 November 2026

Bring EMC screening earlier in development

If the first real EMC check happens after the enclosure, PCB and cables are locked in, there are fewer practical options for fixing problems. Pre-compliance screening lets teams compare design revisions and prepare for formal testing. For suitably sized equipment, a GTEM cell is one option for radiated screening in-house — a complement to formal compliance testing, not a replacement.

View GTEM cellsView EMC test solutions
29 October 2026

Temperature range is only the start of a chamber spec

Two chambers can cover the same temperatures and still suit very different test programmes. Before choosing, define the ramp rates and dwell times, whether humidity is part of the test, the sample size, loading and operating conditions, and the control tolerances your profile requires. Start from the failure mode you need to investigate, then select the equipment.

View environmental test equipment
27 October 2026

Grid testing needs more than a clean AC waveform

With All Energy Australia in Melbourne on 28–29 October: for inverters, battery energy storage and grid-connected equipment, steady-state operation is only part of the picture. Voltage dips, frequency changes and power flowing back from the device under test decide whether you need a programmable AC source or a four-quadrant regenerative grid simulator.

View grid simulatorsView AC power sources
21 October 2026

Single-ended or differential high-voltage drive?

When a load can take differential drive, splitting the voltage swing across two synchronised outputs doubles the effective swing compared with a single output referenced to ground. The Aigtek ATA-2000 series dual-channel amplifiers deliver up to 1600Vp-p (±800Vp) differential output with bandwidth up to DC–1MHz — common in piezoelectric and actuator drive work.

View the ATA-2000 seriesView on LinkedIn
19 October 2026

Thermal shock or rapid temperature change? Our guide

We get asked this a lot, so the answer is now in one place. Thermal shock jumps the part between fixed hot and cold zones; rapid temperature change ramps one chamber fast under control, the method ESS programmes use. The guide also covers two-zone vs three-zone and air vs liquid, with a side-by-side table and the questions to answer before choosing a chamber.

Read the guideView on LinkedIn
12 October 2026

LISUN HIPOT10-100KV AC/DC Hipot Tester

Withstand voltage and insulation testing across a 10–100kV range — a staple on electronics and appliance manufacturers' QA lines for electrical safety compliance.

View productView on LinkedIn
7 October 2026

Rapid temperature change or thermal shock?

The two terms often get used interchangeably, but they describe different tests. Thermal shock moves the part between separate hot and cold zones for a near-instant step change. Rapid temperature change uses a single chamber that ramps quickly between set points. Check which profile your test standard actually calls for before choosing a chamber.

Read the guideView rapid temperature change chambersView thermal shock chambersView on LinkedIn
5 October 2026

ADG+ or ADG-L? Choosing the right Preen DC power supply

Preen's ADG-L (5–15kW, compact 3U) and ADG+ (30–300kW, modular) series solve the same problem at very different scales. We break down how to choose between them for your test line.

Read the guideView DC power suppliesView on LinkedIn
3 October 2026

Air-to-air or liquid-to-liquid thermal shock?

Most thermal shock programs transfer parts through air. Some specifications call for liquid-medium shock instead, which submerges parts in temperature-controlled baths for an even faster transition. Check which method your standard specifies before booking chamber time.

Read the guideView thermal shock chambersView on LinkedIn
1 October 2026

Two-zone or three-zone thermal shock chamber?

Two-zone chambers move parts directly between hot and cold zones, covering standard thermal shock profiles such as MIL-STD-810, MIL-STD-883 and JEDEC. Three-zone chambers add an ambient zone between the extremes, for test profiles that call for an ambient dwell step.

Read the guideView thermal shock chambersView on LinkedIn
October 2026

We're now posting regularly on LinkedIn

Finch Electronic Solutions is sharing more product news, technical guides and updates on LinkedIn — covering EMC & RF, power & energy, electrical safety & compliance, environmental & reliability, and fibre/laser test equipment for engineers and manufacturers across Australia and New Zealand.

About Finch Electronic Solutions
October 2026

What's slowing down your compliance sign-off?

We're asking engineers where compliance testing bottlenecks actually happen — EMC chamber lead times, electrical safety paperwork, environmental test scheduling, or something else — so we can point people to the right gear.

View electrical safety & HV test equipment
October 2026

Why aerospace testing needs pressure and temperature together

Testing temperature tolerance and low-pressure tolerance separately misses the failure mode that actually matters for aircraft, satellite and rocket hardware. Here's what a combined altitude/temperature test profile is checking for.

Read the articleView environmental test equipment
October 2026

LISUN Bulk Current Injection (BCI) Test System

Test immunity to conducted RF disturbance without a full anechoic setup. The standard approach for automotive and aerospace EMC immunity testing, injecting RF current directly onto cable harnesses to simulate real-world interference.

View product
October 2026

One supplier, ten brands

Finch Electronic Solutions is the authorised Australia/NZ distributor for ten manufacturers — RF Technology, RFlight, LISUN, XHFiber, Mactron, MEWOI, Preen, Bonn Elektronik, Aigtek and Sonacme — spanning EMC/RF, power, electrical safety, environmental, lab and fibre/laser equipment.

View our brands
30 September 2026

SHINHO 18S & 18S Pro fusion splicers now in stock

Two new additions to our fusion splicer range — the 18S (active cladding alignment) and the 18S Pro (core-to-core alignment) — covering everything from fast field splicing to the lowest-loss jobs.

View productsRead the comparison guideView on LinkedIn
September 2026

Core-to-core or cladding alignment?

The alignment method is the biggest single difference between fusion splicers. Cladding alignment is fast and well suited to field work; core-to-core alignment targets the lowest splice loss for demanding jobs.

Read the comparison guideView on LinkedIn
More updates are added here as they happen, alongside our LinkedIn page — follow us there for the most frequent posts.