Home /
Laboratory Power Amplifiers & Signal Sources

ATA-3000 Series Power Amplifier

Bandwidth (-3dB) up to DC~300kHz, max output power 1000Wp, CV and CC operation

General-purpose power amplification of AC and DC signals — driving power-type loads without the extreme voltage of Aigtek's dedicated high-voltage series, but with more output power than a lab signal amplifier — covers a broad and practical middle ground in test and drive applications. Aigtek's ATA-3000 Series addresses this segment directly, amplifying AC and DC signals up to 1000Wp of maximum output power.

The ATA-3040C, ATA-3080C and ATA-3090C share a DC~120kHz bandwidth with digitally set gain. The ATA-3100B extends the range to 300kHz and adds constant-current operation, with 280Vp-p, 45Ap continuous and 800VA output for coil, transformer core loss and magnetic particle imaging work.

Bandwidth to 120kHz (-3dB), or 300kHz on the ATA-3100B, gives the ATA-3000 solid dynamic response for its power class, and numerically controlled voltage gain adjustment supports precise, repeatable configuration of output scaling. As a general power amplifier rather than a specialised high-voltage or wide-bandwidth instrument, the ATA-3000 fits applications where driving a power-type load at moderate frequency is the core requirement, without needing the specialised characteristics (extreme voltage, extended bandwidth, PZT-specific matching) that other series in the range are built around.

This positions the ATA-3000 as a practical general-purpose choice — where an application's requirements are straightforward power amplification within a moderate frequency range, it covers that need without the added cost of specification the application doesn't actually use.

ATA-3000 Series Power Amplifier
Inquire About This Range →
Aigtek ATA-3000 Series Power Amplifier
ATA-3000 Series Power Amplifier
Up to 1000Wp and DC~300kHz. Drives power-type loads, with digitally set gain on the C models and constant-voltage or constant-current operation on the ATA-3100B.
Enquire About This Series →
ModelBandwidth (-3dB)VoltageCurrentPowerOutput 
ATA-3040C Power AmplifierDC~120kHz100Vp-p(±50Vp)10Ap500WpSingleEnquire
ATA-3080C Power AmplifierDC~120kHz160Vp-p(±80Vp)10Ap800WpDifferentialEnquire
ATA-3090C Power AmplifierDC~120kHz100Vp-p(±50Vp)20Ap1000WpSingleEnquire
ATA-3100B Power AmplifierDC~300kHz (±20Vp)
DC~50kHz (±140Vp)
280Vp-p(±140Vp)45Ap (52Ap pulsed)800VASingleEnquire
Model Details
ATA-3040C Power Amplifier: Introduction, Full Specifications & Datasheet
Product Introduction

The ATA-3040C is a power amplifier capable of amplifying both AC and DC signals, with a maximum output power of 500Wp to drive high-power loads. Gain is digitally adjustable with one-click saving of common settings, it is compatible with mainstream signal generators, and the wide-range power supply accommodates different regional power standards.

LCD Panel DisplayDynamically shows device status and parameters, offering a clear and intuitive interface.
Voltage GainDigitally adjustable 0~30x, with coarse (1 step) and fine (0.1 step) adjustment modes.
InputBNC interface accepting 0~10Vp-p MAX, with selectable 50Ω or 100kΩ input impedance.
OutputBanana sockets, max output 100Vp-p (±50Vp), max output current 10Ap.
ApplicationsUltrasonic testing, electromagnetic testing, battery testing, semiconductor testing.
Specifications
ModelATA-3040C
Output TypeSingle-ended Output
Bandwidth (-3dB)DC~120kHz
Maximum Output Voltage100Vp-p (±50Vp)
Maximum Output Current5Ap (DC~50Hz)  10Ap (>50Hz)
Maximum Output Power500Wp
Fuse10A/250V
Voltage Gainx0~30 (0.1 step/1 step)
Load RL Upper Limit≥9.9Ω (DC~50Hz)  ≥4.9Ω (>50Hz)
DC Bias Adjustment±50V (0.1V step/1V step)
Output Impedance0.1Ω
Input Impedance50Ω / 100kΩ
Input Amplitude0~10Vp-p MAX
Output Voltage Error≤±3% FS @ 1kHz
Voltage Monitoring20mV/V (±5% @ Output, FS)
Current Monitoring0.1V/A (±5% @ Output, FS)
Slew Rate≥26.6V/μs
Total Harmonic Distortion (THD)≤0.1% @ 1kHz, 100Vp-p
Output Voltage Drift≤±0.05V
Ripple≤0.01Vrms
Output Interface4mm Banana socket
ProtectionShort Circuit, Over Voltage and Over Temperature Protection
Signal GroundConnected to chassis and power line ground
Others
Power Supply VoltageAC110~240V, 50/60Hz
Operating Temperature0°C~45°C
Storage Temperature-20°C~50°C
Working Humidity≤80% RH, non-condensing
Warranty1 year
Dimensions440×149×535mm (W×H×D)
Full specification table as published by Aigtek. Contact Finch to confirm current specifications before ordering.
Technical Documentation

Download the full technical datasheet for the ATA-3040C Power Amplifier, published by Aigtek.

⬇ Download Datasheet (PDF) Enquire About ATA-3040C →
ATA-3080C Power Amplifier: Introduction, Full Specifications & Datasheet
Product Introduction

The ATA-3080C is a power amplifier capable of amplifying both AC and DC signals, with a maximum output power of 800Wp to drive high-power loads. Gain is digitally adjustable with one-click saving of common settings, it is compatible with mainstream signal generators, and the wide-range power supply accommodates different regional power standards.

LCD Panel DisplayDynamically shows device status and parameters, offering a clear and intuitive interface.
Voltage GainDigitally adjustable 0~60x, with coarse (1 step) and fine (0.1 step) adjustment modes.
InputBNC interface accepting 0~10Vp-p MAX, with selectable 50Ω or 100kΩ input impedance.
OutputBanana sockets, max output 160Vp-p (±80Vp), max output current 10Ap.
ApplicationsUltrasonic testing, electromagnetic testing, battery testing, semiconductor testing.
Specifications
ModelATA-3080C
Output TypeSingle-ended Output
Bandwidth (-3dB)DC~120kHz
Maximum Output Voltage160Vp-p (±80Vp)
Maximum Output Current5Ap (DC~50Hz)  10Ap (>50Hz)
Maximum Output Power800Wp
Fuse10A/250V
Voltage Gainx0~60 (0.1 step/1 step)
Load RL Upper Limit≥15.9Ω (DC~50Hz)  ≥7.9Ω (>50Hz)
DC Bias Adjustment±80V (0.1V step/1V step)
Output Impedance0.1Ω
Input Impedance50Ω / 100kΩ
Input Amplitude0~10Vp-p MAX
Output Voltage Error≤±3% FS @ 1kHz
Voltage Monitoring20mV/V (±5% @ Output, FS)
Current Monitoring0.1V/A (±5% @ Output, FS)
Slew Rate≥42.6V/μs
Total Harmonic Distortion (THD)≤0.1% @ 1kHz, 100Vp-p
Output Voltage Drift≤±0.05V
Ripple≤0.01Vrms
Output Interface4mm Banana socket
ProtectionShort Circuit, Over Voltage and Over Temperature Protection
Signal GroundConnected to chassis and power line ground
Others
Power Supply VoltageAC110~240V, 50/60Hz
Operating Temperature0°C~45°C
Storage Temperature-20°C~50°C
Working Humidity≤80% RH, non-condensing
Warranty1 year
Dimensions440×149×535mm (W×H×D)
Full specification table as published by Aigtek. Note: Aigtek's specification table lists single-ended output for the ATA-3080C, while its series listing shows differential output. Contact Finch to confirm the output configuration before ordering.
Technical Documentation

Download the full technical datasheet for the ATA-3080C Power Amplifier, published by Aigtek.

⬇ Download Datasheet (PDF) Enquire About ATA-3080C →
ATA-3090C Power Amplifier: Introduction, Full Specifications & Datasheet
Product Introduction

The ATA-3090C is a power amplifier capable of amplifying both AC and DC signals, with a maximum output power of 1000Wp to drive high-power loads. Gain is digitally adjustable with one-click saving of common settings, it is compatible with mainstream signal generators, and the wide-range power supply accommodates different regional power standards.

LCD Panel DisplayDynamically shows device status and parameters, offering a clear and intuitive interface.
Voltage GainDigitally adjustable 0~30x, with coarse (1 step) and fine (0.1 step) adjustment modes.
InputBNC interface accepting 0~10Vp-p MAX, with selectable 50Ω or 100kΩ input impedance.
OutputBanana sockets, max output 100Vp-p (±50Vp), max output current 20Ap.
ApplicationsUltrasonic testing, electromagnetic testing, battery testing, semiconductor testing.
Specifications
ModelATA-3090C
Output TypeSingle-ended Output
Bandwidth (-3dB)DC~120kHz
Maximum Output Voltage100Vp-p (±50Vp)
Maximum Output Current10Ap (DC~50Hz)  20Ap (>50Hz)
Maximum Output Power1000Wp
Fuse10A/250V
Voltage Gainx0~30 (0.1 step/1 step)
Load RL Upper Limit≥4.9Ω (DC~50Hz)  ≥2.4Ω (>50Hz)
DC Bias Adjustment±50V (0.1V step/1V step)
Output Impedance0.1Ω
Input Impedance50Ω / 100kΩ
Input Amplitude0~10Vp-p MAX
Output Voltage Error≤±3% FS @ 1kHz
Voltage Monitoring20mV/V (±5% @ Output, FS)
Current Monitoring0.05V/A (±5% @ Output, FS)
Slew Rate≥26.6V/μs
Total Harmonic Distortion (THD)≤0.1% @ 1kHz, 100Vp-p
Output Voltage Drift≤±0.05V
Ripple≤0.01Vrms
Output Interface4mm Banana socket
ProtectionShort Circuit, Over Voltage and Over Temperature Protection
Signal GroundConnected to chassis and power line ground
Others
Power Supply VoltageAC110~240V, 50/60Hz
Operating Temperature0°C~45°C
Storage Temperature-20°C~50°C
Working Humidity≤80% RH, non-condensing
Warranty1 year
Dimensions440×149×535mm (W×H×D)
Full specification table as published by Aigtek. Contact Finch to confirm current specifications before ordering.
Technical Documentation

Download the full technical datasheet for the ATA-3090C Power Amplifier, published by Aigtek.

⬇ Download Datasheet (PDF) Enquire About ATA-3090C →
ATA-3100B Power Amplifier: Introduction, Full Specifications & Datasheet
Product Introduction
Aigtek ATA-3100B Power Amplifier front panel

The ATA-3100B is a power amplifier for both AC and DC signals, with up to 800VA of output power, 280Vp-p and 45Ap continuous (52Ap pulsed) to drive coils, transformers and other power-type loads. It runs in constant-voltage (CV) or constant-current (CC) mode, and its bandwidth extends to 300kHz at ±20Vp, 200kHz at ±40Vp and 50kHz at full ±140Vp swing. Gain is set with a front-panel rotary knob, so it pairs simply with any standard signal generator, and the wide-range mains input suits power standards worldwide.

Front-Panel ControlsRotary gain knob; Run, Stop and Reset pushbuttons; LED indicators for run, standby, fault, overvoltage, overload and overtemperature.
Voltage Gainx20, adjustable from 0% to 100%.
InputBNC interface, 10kΩ input resistance, accepts 0~20Vp-p MAX.
Output3-position barrier terminal block, max 280Vp-p (±140Vp), 45Ap continuous, 52Ap pulsed.
ApplicationsEMC testing, transformer core loss characterisation, degaussing/demagnetisation, magnetically actuated robotics, magnetic particle imaging (MPI), automotive electronics testing, current sensor characterisation.
Specifications
ModelATA-3100B
Output TypeSingle-ended Output
Operating ModesConstant-voltage (CV) and constant-current (CC)
Bandwidth (-3dB)DC~300kHz (±20Vp)
DC~200kHz (±40Vp)
DC~50kHz (±140Vp)
Maximum Output Voltage280Vp-p (±140Vp)
Maximum Continuous Current45Ap
Maximum Pulsed Current52Ap (20% duty @ 40ms)
Maximum Output Power800VA
Fuse10A/250V
Voltage Gainx20, adjustable 0~100%
Output Resistance0.04Ω
Input Resistance10kΩ
Input Amplitude0~20Vp-p MAX
Output Voltage Error≤±3% FS @ 1kHz
Total Harmonic Distortion (THD)≤0.5% @ 1kHz, 140Vp-p
Input InterfaceBNC
Output Interface3-position barrier terminal block
ProtectionOvercurrent, Over Voltage and Over Temperature Protection
PushbuttonsRun, Stop, Reset
LED IndicatorsWork, Standby, Fault, Overvoltage, Overload, Overtemperature
Signal GroundConnected to chassis and power line ground (PE)
Others
Power Supply VoltageAC110~240V, 50/60Hz
Operating Temperature0°C~45°C
Storage Temperature-20°C~50°C
Working Humidity≤80% RH, non-condensing
Warranty1 year
Dimensions440×104×528mm (W×H×D)
AccessoriesPower cord, BNC cable, red/black output lead set, spare fuse, 2× 2.7Ω/2W resistors, user manual, user guide, certificate of conformance, calibration certificate
AC Output by Load (100Hz)

Pulse figures are 40ms at 20% duty cycle; 5min and 1h figures are at 100% duty cycle. Choose the mode that matches your load impedance: high-voltage for 4–16Ω, medium-level for 0.5–4Ω, high-current for 0.5–1Ω.

High-Voltage Mode
16Ω loadPeak 158Vp / 9.8Ap (pulse, 5min and 1h); RMS 112Vrms / 6.9Arms, 773VA for 1h
8Ω loadPeak 154Vp / 19Ap (pulse), 136Vp / 16Ap (5min, 1h); RMS 96Vrms / 11.5Arms, 1104VA for 1h
4Ω loadPeak 124Vp / 31Ap (pulse), 108Vp / 25.7Ap (5min), 61Vp / 14.5Ap (1h); RMS 43Vrms / 10.3Arms, 443VA for 1h
2Ω loadPeak 98Vp / 49Ap (pulse only)
Medium-Level Mode
4Ω loadPeak 72Vp / 18Ap (pulse), 69Vp / 16.4Ap (5min, 1h); RMS 49Vrms / 11.6Arms, 568VA for 1h
2Ω loadPeak 61Vp / 30Ap (pulse), 57Vp / 26.2Ap (5min, 1h); RMS 40Vrms / 18.5Arms, 740VA for 1h
1Ω loadPeak 47Vp / 47Ap (pulse), 43Vp / 39.6Ap (5min), 21Vp / 21Ap (1h); RMS 15Vrms / 14.8Arms, 222VA for 1h
0.5Ω loadPeak 26Vp / 52Ap (pulse only)
High-Current Mode
1Ω loadPeak 29Vp / 29Ap (5min, 1h); RMS 20.5Vrms / 20.5Arms, 420VA for 1h
0.75Ω loadPeak 26Vp / 34Ap (5min, 1h); RMS 18Vrms / 24Arms, 432VA for 1h
0.5Ω loadPeak 22.7Vp / 45Ap (5min, 1h); RMS 16Vrms / 32Arms, 512VA for 1h
Conditions not listed were not tested.
Technical Documentation

Ask us for the full ATA-3100B datasheet, including the complete AC output tables.

Enquire About ATA-3100B →
Related Series
ATA-300 Series
ATA-300 Series
High-power amplifier, up to 4000Wp, 80A
ATG-3000 Series
ATG-3000 Series
Power signal generator, DC~100kHz
ATG-300 Series
ATG-300 Series
Power signal generator, DC~30kHz

Frequently Asked Questions

What kind of loads is the ATA-3000 built to drive?

General power-type loads requiring AC or DC signal amplification up to 1000Wp — a broad category covering many standard power amplification test and drive applications that don't call for the extreme voltage or specialised load-matching of Aigtek's more specialised series.

How does the ATA-3000 compare to the higher-power ATA-300 series?

The ATA-300 series reaches a higher maximum output power, up to 4000Wp. Where an application needs substantially more raw output power, the ATA-300 is the appropriate choice; where up to 1000Wp at up to 120kHz is sufficient, or 800VA and 45Ap at up to 300kHz with the ATA-3100B, the ATA-3000 covers the requirement.

What does numerically controlled voltage gain adjustment provide over a manual analog control?

Numerical control gives precise, repeatable gain settings that can be dialled in exactly and reproduced consistently across test sessions, avoiding the drift or imprecision that can come with a purely manual analog gain adjustment.

See Aigtek's technical documentation for the ATA-3000 series →

Send an Enquiry →Send an Enquiry →

Related Reading

Read: Constant-Voltage vs Constant-Current Amplifiers — Driving Coils, Transformer Cores and MPI

Read: Driving Electromagnetic Coils — Why Current Output Matters More Than Voltage