Programmable DC power supplies range from a single benchtop unit to megawatt rack systems, and the headline voltage and power figures don’t tell you which one fits your test. This guide works through the specifications in the order that matters, so you end up with a supply that runs your profile without paying for capability you don’t need.


1. Start With the Voltage and Current Your Device Actually Needs

List the highest voltage and the highest current your device under test will draw, and at what voltage that current occurs. Then add margin, typically 10–20%, for transients, cable drop and future work.

Check the supply’s power envelope, not just its maximum voltage and current. A conventional (rectangular) supply delivers full current only up to its maximum voltage, so a 500 V, 30 A supply rated at 15 kW is limited by power, not current, at the top of its range. An autoranging supply trades voltage for current along a constant-power curve, so one unit can cover both a high-voltage, low-current test and a low-voltage, high-current test. If your tests span a wide voltage range, autoranging can replace two supplies.


2. Decide Whether You Need Bidirectional (Regenerative) Operation

A unidirectional supply only sources power. A bidirectional supply can also sink power, which is what battery charge/discharge cycling, motor drive regeneration and some burn-in tests require. Regenerative designs return the absorbed energy to the grid instead of burning it as heat, which cuts running costs and cooling load in long tests.

If your device ever pushes current back into the supply, you need a bidirectional unit or a separate electronic load. Our guide to bidirectional vs unidirectional DC power supplies covers the trade-off in detail.


3. Check Ripple, Noise and Accuracy

Sensitive analogue, RF and sensor circuits can misbehave on a noisy supply even when the average voltage is correct. Compare ripple and noise figures measured the same way (peak-to-peak and rms, over a stated bandwidth), and check setting and readback accuracy if the supply is also your measurement instrument. See why ripple and noise matter more than the headline power rating.


4. Look at Transient Response and Programming Speed

If your test changes voltage quickly, such as automotive cranking profiles, battery emulation or load-step testing, you need to know how fast the supply responds. Two figures matter:

Many supplies also offer list or sequence modes that run a stored voltage profile without a PC in the loop, which gives more repeatable timing.


5. Choose the Form Factor

Form factorTypical powerBest for
BenchtopUp to a few kWR&D, design validation, education
Rack-mountAround 1 kW to tens of kW per unit, paralleled for moreProduction test, ATE, burn-in racks
Cabinet or towerTens of kW to MWEV battery packs, PV inverters, energy storage, power electronics

For a deeper comparison, see rackmount vs module-based cabinet vs tower-type architectures.


6. Plan for Control, Paralleling and Protection


7. Think About Installation in Australia

Higher-power supplies usually need a three-phase supply, so confirm input voltage and current before ordering. Regenerative units feed power back into the site supply, which may need to be checked with your facilities team. Local service and calibration support matter more as the system gets bigger.


Quick Selection Checklist

  1. Maximum voltage and current, with margin
  2. Rectangular or autoranging power envelope
  3. Source only, or bidirectional/regenerative
  4. Ripple, noise and accuracy limits
  5. Transient response and programming speed
  6. Benchtop, rack or cabinet
  7. Interfaces, paralleling and protection
  8. Site power, cooling and local support

Not sure which supply fits your test? Send us your test specification and we’ll recommend a configuration.


Frequently Asked Questions

What is the difference between a programmable DC power supply and a bench power supply? A basic bench supply is set by hand and suits simple lab work. A programmable supply can be controlled from software, run voltage sequences and log measurements, which is what automated and production testing needs. See our bench power supplies for simpler requirements.

Do I need an autoranging supply? Only if your tests cover a wide range of voltages and currents. If you always test near one operating point, a conventional supply sized for that point is usually cheaper.

When should I choose a regenerative supply? When your device returns energy, such as batteries or motor drives, or when long tests at high power would waste a lot of energy as heat.


Related Products